Interior Foam Insulation | Open Cell, Closed Cell Spray Insulation | Lincoln, Omaha, Kearney

Interior Foam Insulation

Interior spray foam insulation, for buildings, eliminates drafts and makes a structure highly energy efficient which helps it to be more comfortable all year round. This type of spray on insulation is considered to be the best, home, wall insulation or attic insulation by far.

The first thing you need to know about interior spray foam insulation, or commonly called wall foam, is that there are two main types:

Open-cell and Closed-cell

When it comes time to actually put the spray on insulation, like interior spray foam insulation, in your home or commercial building structure, you must know if you are buying 0.5 lb./cu. ft. (open cell) or 2.0 lb./cu. ft. (closed cell). This makes a big difference in cost and performance. The lb./cu. ft. refers to density. The less dense the interior spray foam insulation is, the softer it makes it. This affects R-value and insulation performance.

Open-cell interior spray foam insulation is where tiny cells of the spray foam are open. These half open cells have air in them instead of trapped gas. This makes the interior spray foam insulation weaker or softer feeling than closed-cell foam. Open cell spray foam insulation typically weighs in at 0.4 to 0.5 lb./cu. ft.

Closed-cell spray foam insulation is formed with small and tiny cells of the spray foam that are closed. Having Tillotson Enterprises install a closed-cell spray foam insulation instead of other conventional insulations, you’ll get a seamless air barrier that eliminates air leakage in the building envelope. This, in turn, will allow the use of smaller HVAC equipment, reduce sound transmission, and help prevent outdoor air infiltration and the penetration of dust, pollen and other allergens.

  • Higher energy efficiency – Exceptional air sealing and R-values result in heating and cooling cost savings. Drafts are virtually eliminated, and a more constant and comfortable indoor environment and temperature is maintained.
  • Better moisture and condensation control – Closed-cell spray foam offers superior performance in resisting moisture transmission and condensation.
  • Increases structural strength – Research has shown 2×4 stud walls with closed-cell spray foam can support significantly greater loads than other insulation materials.
  • Improved indoor air quality – Helps prevent the introduction of dust, pollen and other allergens into the living environment. An excellent choice for people with allergy problems.
  • Helps control insects and rodents – Closed-cell foam helps control insects and rodents from entering the building because it acts as a continuous and seamless building envelope barrier.
  • Can be used in a wide range of applications – Can be used in both wood and metal framed structures, including walls, floors, ceilings, under roof decks, on attic floors, crawl spaces, basements and foundations.

Closed cell spray foam is filled with a gas not air as in open cell foam. This gas helps the spray foam insulation rise and expand. This trapped gas is a better insulator; about twice that of open cell. Closed cell spray foam insulation densities are greater which means they are heavier and resistant to puncture. Closed cell spray foam insulation densities used from interior range from 1.7 lb./cu. ft. to 2.0 lb./cu. ft. Roofing spray foam applications typically use a 2.8 to 3.0+ lb./cu. ft. to support foot traffic. The higher the density of the spray foam, the heavier or stronger it becomes.

The advantages of closed-cell spray foam insulation:

  • Greater compression strength (denser).
  • Higher R-value.
  • Air barrier with less thickness applied.
  • Vapor retarder at 2″ thick.

The advantages of open-cell spray foam insulation:

  • Requires less material and therefore less expensive.

What open cell and closed cell spray foam insulation have in common:

  • Both can be an air barrier.
  • The choice of spray on insulation can also be based on applications and performance requirements, such as strength, vapor control, available space, etc. For example, open-cell spray foam insulation has an R-value around 3.5 per inch, typically, and closed cell spray on insulation has an R-value of around 6.5 per inch. If you have a 2 x 4 wall, you can only get R-12 with open cell spray foam, but you can achieve an R-21 with closed-cell spray foam.
  • Both types of spray on insulation are used in building applications and the choice can depend on many factors. Some spray on insulation is not to be used in certain applications. For example, you wouldn’t use open-cell spray foam insulation in basements or below grade where spray on insulation could absorb water. This would make its thermal performance drop and become zero; because water is a poor insulator.

Interior Spray Foam Insulation Improves the Building Envelope

The building envelope contains several construction systems, materials and design components that control the temperature, movement of air, and moisture both into and out of the building. A building’s insulation, air barrier and vapor barrier all need to work together to achieve a stable environment.

Build it Tight, Ventilate Right.

Ventilating the attic and crawl spaces has been the requirement of a traditional code method. Ventilation of these spaces was required because standard materials and building design were not capable of addressing radiant heat transfer, condensation, and the results of “stack-effect issues.” Therefore, the answer to address heat transfer, the formation of moisture from condensation and air infiltration, was to ventilate these attics and crawl spaces.

Ventilating attics and crawl spaces brings with it air moisture, pollution and other adverse problems. These, vents allow places where insects and rodents can enter, and conditioned air can escape from the living space. Most of the time, our heating/cooling utility ducts are located in the attic and/or crawl spaces. The temperature of attic and crawl spaces make ducts lose up to 10% or more of the hot or cold air flowing through the duct work, due to radiant transfer. Worse yet, moisture and mold can also form within these ducts, when certain temperature differences occur. This can cause adverse health effects to those who occupy these buildings. Extreme temperature changes can cause condensation and the potential for developing mold. Air conditioning systems will also need to work harder, which consumes more energy. Most builders and design professionals are not familiar with modern materials and progressive building science techniques that can virtually eliminate all of these problems that force the traditional, less effective requirement for ventilation in these building spaces. Builders and design professionals will also make the argument that your home needs to breathe. Well, they are absolutely correct. Let us help you keep your home tight, healthy and energy efficient, and let the mechanical ventilation systems due the job properly. Interior spray foam insulation can still provide benefits far greater than traditional materials, such as fiberglass and cellulose, regardless of whether you decide to ventilate these spaces or not. By using interior spray foam insulation, you can increase your home’s energy performance, structural integrity and air quality. In wood frame construction, the weight of the roof, shingles, standing water, and snow add weight that pushes downward on the walls called compressive force. Strong winds and gusts also impose lateral forces onto your building’s walls. These forces can distort the walls which is called “shearing force”. However, when walls are built with minimum standards, movement can cause cracks and other structural problems. Closed cell interior spray foam for wall insulation has a higher density, adheres to studs and surrounding exterior which strengthens both. This added strength makes wall movement less; due to winds and other forces. This makes the walls strong enough to meet codes for hurricanes or other strong winds.

Spray Foam Insulation for Attic or Vented Spaces

Today attics are vented through gable, soffit, and ridge vents in the roof. Using spray on insulation in attics with design principles from architect or builders using traditional vented attics insulation. Here Insulation is laid on attic floor to insulate the ceiling from heat or cold. In spray on insulation, like spray foam insulation, we simply replace traditional fiberglass batts, or cellulose, with spray foam. A vented attic will become approximately 130-degrees in the summer. This makes air-conditioning have to work harder and, also can create moisture and mold problems. Spray foam insulation creates a thermal barrier between the attic and the temperature-controlled living or working spaces below.